Forum FAQForum FAQ SearchSearch MemberlistMemberlist   UsergroupsUsergroups RegisterRegister ProfileProfile Log in to check your private messagesLog in to check your private messages Wim's BIOS RSS FeedRSS Log inLog in

ASUS P5B Mobo BIOS Question

 
Post new topic   Reply to topic    Wim's BIOS Forum Index -> General

Recommended by Wim's BIOS...

BIOS Agent scan: Upgrade your BIOS! Driver Agent scan: Instant Access to 116,215 Device Drivers Updates!

View previous topic :: View next topic  
Author Message
p23185
New visitors - please read the rules.


Joined: 07 Feb 2007
Posts: 3

PostPosted: Wed Feb 07, 2007 5:26 am     Post subject: ASUS P5B Mobo BIOS Question Reply with quote

Does anyone know if Asus P5B Mobo's BIOS (from Asus website spec: 8 Mb Flash ROM, AMI BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.3, ACPI 2.0a, ASUS EZ Flash 2, ASUS CrashFree BIOS 3) will operate in a 64bit mode? I am contemplating a purchase and will have Intel Core 2 Duo and eventually Microsoft Vista. The Intel info says make sure the BIOS will support. Before I purchase the Mobo I would like to know if I can eventually upgrade to 64 bit somewhere down the road.
Back to top
View user's profile Send private message
edwin
The Hardware Archivist


Joined: 20 Mar 2002
Posts: 4331
Location: Netherlands

PostPosted: Wed Feb 07, 2007 6:25 pm     Post subject: Reply with quote

It is Core2 Duo compatible:
http://www.asus.com.tw/products.aspx?l1=3&l...8&modelmenu=1

I'm just not sure what you mean exactly with 64bit mode support.
_________________
edwin/evasive

Do not assume anything

System error, strike any user to continue...
Back to top
View user's profile Send private message Send e-mail Visit poster's website
p23185
New visitors - please read the rules.


Joined: 07 Feb 2007
Posts: 3

PostPosted: Tue May 01, 2007 8:07 pm     Post subject: ASUS P5B Mobo BIOS Question - IDE set as SATA Reply with quote

I am hacving DVD Burner problems and cannot get the DMA to report on in Nero even though the IDE controllers report it set to DMA if Available, Mode 5. I have used the Regedit procedure, and the IDE uninstall procedure to reset the CRC problem (6 and down to PIO). BUT Nero always logs the DMA as off in the the burner logs, whether the burn failed or was sucessful.

In my BIOS "IDE Config" says it is set to SATA confiig [Enhanced] - right below it says "Config SATA as [IDE]. Options under here are "IDE" or "AHCI" I have prim and sec SATA drives and a third PATA drive connected as slave on the parallel IDE cable, with Mem 16X DVD burner as the master. What should the setting be for "IDE Config"?

When I look inside Windows XP Home, Device Manager I see IDE controllers for 2 port SATA, 4 port SATA, two Primary IDE channels and two Secondary IDE channels, EVEN THOUGH MY MOBO only has ONE PATA connector.

Lastly, does anyone have a reference I can go to that would help me understand the hybrid SATA and PATA drive setup? Most stuff I have found either address SATA OR PATA but not combined.
Back to top
View user's profile Send private message
edwin
The Hardware Archivist


Joined: 20 Mar 2002
Posts: 4331
Location: Netherlands

PostPosted: Wed May 02, 2007 8:57 pm     Post subject: Reply with quote

Sounds more like an issue with either Nero not recognizing the DVD-burner capabilities properly and/or older firmware problem on the DVD-drive.
_________________
edwin/evasive

Do not assume anything

System error, strike any user to continue...
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic    Wim's BIOS Forum Index -> General All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group